Design, connect andvalidate embedded electronics
ELC is the Electronics service of WRE. It develops analog and digital electronics, printed circuit boards, firmware and embedded systems for connected equipment, prototypes and industrial applications.
Engineering from electronic function to tested connected device
ELC translates a functional need into a controlled electronic architecture, combining components, power supplies, inputs and outputs, processors, firmware and communication interfaces.
The service can support a targeted study or a complete development sequence including feasibility, schematics, PCB, prototype bring-up, embedded software, communication, testing and technical documentation.
Hardware, firmware and connectivity engineered together
The three technical layers are coordinated to reduce interface risks and prepare the product for integration, testing and future evolution.
Analog, digital and power electronics
Functional analysis, component sizing, power architecture, signal conditioning, sensor and actuator interfaces, protection, schematics and PCB design.
Prepare an electronic design with documented interfaces, selected components, manufacturing outputs and measurable verification criteria.
Electronic design servicesMicrocontrollers and firmware
Firmware architecture, board support, peripheral drivers, data acquisition, actuator control, state machines, real-time tasks, diagnostics and controlled updates.
Develop structured firmware with defined states, interfaces, version control, test points and recovery behavior.
Firmware servicesCommunication and connected devices
Integration of local buses, wired and wireless connectivity, device protocols, edge processing and secure transfer toward applications, gateways or cloud platforms.
Connect the device to sensors, equipment and software platforms through documented data models and reliable communication behavior.
Connectivity servicesElectronic and embedded services throughout the development lifecycle
The scope is adapted to the maturity of the project, available inputs, target environment, production volume and required verification level.
Feasibility and requirements
Analysis of functions, environment, interfaces, power, performance, risks, constraints and expected lifecycle.
- Functional requirements
- Technology assessment
- Cost and feasibility review
Electronic architecture
Definition of functional blocks, processors, memory, power supplies, interfaces, protection and test points.
- Block diagrams
- Component selection
- Interface definition
Schematics and PCB
Creation and review of schematics, board layout, manufacturing files and assembly documentation.
- Analog and digital schematics
- PCB layout and review
- Manufacturing outputs
Firmware development
Low-level drivers, acquisition, control logic, state machines, diagnostics, communications and update mechanisms.
- STM32 / ARM
- Drivers and peripherals
- Real-time tasks
Prototype and bring-up
Preparation of prototypes, initial power-up, measurements, firmware loading, interface checks and anomaly investigation.
- Assembly coordination
- Board bring-up
- Debug and correction
Sensors and actuators
Integration of measurement chains, conditioning, calibration, actuator drivers and diagnostic feedback.
- Sensor acquisition
- Signal conditioning
- Actuator control
Communication and IoT
Local and remote communication, gateways, device protocols and integration with APIs or supervision platforms.
- CAN / UART / SPI / I²C
- Ethernet / Wi-Fi / Bluetooth / LoRa
- MQTT / HTTPS
Testing and validation
Verification of electronic functions, power behavior, firmware, interfaces, communication and fault handling.
- Bench tests and measurements
- Interface and protocol tests
- Validation records
Industrialization support
Preparation of technical files, test strategy, controlled revisions, obsolescence analysis and production support.
- Bill of materials and files
- Production test support
- Change and obsolescence management
A controlled path from electronic need to validated prototype
The method maintains consistency between requirements, hardware, firmware, interfaces, test evidence and project documentation.
Requirements and feasibility
Qualification of functions, environment, interfaces, power budget, data, constraints, risks and expected verification.
Electronic and firmware design
Definition of hardware blocks, component choices, schematics, PCB strategy, firmware architecture and communication interfaces.
Prototype preparation and bring-up
Coordination of boards, firmware, assembly and initial checks under controlled versions and documented configurations.
Testing and validation
Verification of electronic, firmware, communication and fault-handling behavior against approved requirements.
Technical handover and lifecycle support
Delivery of agreed files, source code, firmware builds, test evidence and maintenance information.
Understanding the ELC service
ELC is the Electronics service within WRE. It covers electronic design, PCB development, microcontrollers, firmware, sensors, communication interfaces and embedded systems.
Depending on scope, ELC can support requirements, architecture, schematics, component selection, PCB layout, firmware, assembly coordination, bring-up and validation.
Depending on the project, ELC can integrate CAN, UART, SPI, I2C, USB, Ethernet, Wi-Fi, Bluetooth, LoRa, MQTT, HTTPS and other suitable interfaces.
Yes. Subject to available files and access, ELC can analyze an existing board, firmware or prototype, identify risks and support correction, redesign, migration or controlled evolution.
Useful inputs include the functional need, environment, power source, inputs and outputs, communication interfaces, dimensions, target quantities, existing schematics or source code, compliance constraints and schedule.
Turn an electronic function into a controlled embedded solution
Present the required function, environment, interfaces, available inputs and expected results. Our team will identify the appropriate electronic, firmware and validation activities.